Reviews
Fits: YAMAHA WR250R, YAMAHA WR250X
Too many O-rings and Large help!
WR250 has many small O-rings, but they are all in Kit, which is very convenient! 。 If you are doing the work yourself, please be very careful about the direction of the filter. If it is facing the other way, the oil will not circulate. 。 If it had been running normally up to that point, it should have been in the correct orientation, so just remember the orientation when you remove it. View detail
easy to install nice fit
quite nice fit with gb350c This make bike more qute and classic. This can not make any wind flow change but fine! Bcuz this make bike look hansome. Moreover, this is very easy to install to the bike. Only 2 botls need to be pull over and put it again. It takes 10minute to install. I have never dissapointed with daytona product yet! View detail
For July Spec.
Mirror on GSX-8R Tuned by JURI Spec. to "1".
Since the original position is now Handlebar Mounting,
The field of view is a little narrower, but not particularly problematic.
I am very satisfied with the result.
Mirror has no wobble and a wide range of adjustment,
The essence is also good.
View detail
Surprisingly useful
Product Name
DAYTONA DAYTONA Helmet-in Pocket
Item Number
77008
Vehicles
CYGNUS X (Taiwan Type 2)
Number of man-hours
About 10 minutes
Required Tools
Torque wrench, hexagon socket, Hexagon socket, Extension bar, Combination wrench, Driver, Hammer, Pliers, etc.
Why did you choose this product?
I was concerned about small items being scattered around in the Helmet inSpace and was looking for items that could be organized and stored. 。
Was the one you received as per Image?
Yes, the NylonMaterial is more solid than I imagined, and the Magic tape is carefully sewn and finished. 。
Was the installation difficult?
Installation is very easy, just stick it on with the included Surface Fastener. No special tools are required, and it took only 5 to 10 minutes! 。
How was your experience with it?
The Helmet in is now much more organized, as I can refreshingly store small items such as gloves, USB cable, air gauge, etc. It is also very practical as it does not gap or fall off while riding. 。
[Included Parts:were they on?
Several Surface Fasteners are included in the package, allowing for flexible adjustment of the mounting position. It is also nice to have a spare. 。
[Was there anything that disappointed you?
I would have liked it to be a little deeper to make it easier to store thicker tools and other items, but it is sufficient for everyday use. 。
Point and hang of installation
If you degrease the surface before attaching, the adhesive strength will last longer. (When attaching to curved surfaces, warm the surface slightly with a dryer or the like to improve adhesion. 。
Opinions and Requests to the ▼Manufacturer
I think it is simple, convenient, and good items!
View detail
Ideal for roadside station breaks
I used to carry a helmet or put it in my top case, but when I was on a long-distance tour or had a lot of luggage, I had a lot of trouble.
I was looking for a better way to use it, especially when taking a break at a roadside station, but when I learned about it on WebigNews, I thought about it.
Since there are ETCAntennas and USB sockets around the handlebar, I thought a slim type would be better, so I installed it.
When I used it and saw it, it is convenient. What was a failure was that it would have been more convenient if I had used it with Wire, which I regret a little.
View detail
Fits: HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 50, HONDA APE 100, HONDA APE 100, HONDA APE 100, HONDA APE 100, HONDA APE 100, HONDA APE 100, HONDA APE 100, HONDA APE 100, HONDA XR50 MOTARD
Good Stuff
Came in a timely manner for the long distance to the states. Came before all of my other parts. I ordered lots of parts and nothing was missing. In regards to the pump, tight clearance with return spring that sits under it but seems to work well so far! Honda 1986 Honda XR100R View detail
This tool sure makes cleaning up the chain a whole lot easier and a faster process
About quality and texture, I can confirm that the quality is great and that the materials used is a mixture of ABS (Acrylonitrile Butadiene Styrene) plastic for the body and nylon for the brushes. About the feeling of use, This tool sure makes cleaning up the chain a whole lot easier and a faster process. The features that help to achieve this are the stiff nylon brushes on both ends and the three sided brush head. Products to buy together, To further increase your capabilities to clean/lubricate more of your motorcycle a wire injector would be ideal to also add to your cart, to be used on your clutch and throttle cables to help keep their operation smooth and long lating. Difficulty of installation, I can say the fitment of the chain brush is very easy due to the simple nature of it's use caused by it's design using stiff brushes and a three sided head. Cost performance and comparison with other products, The pricing of this chain brush is great, designed for one purpose and faster then using then a standed brush that is not specifically for this purpose. About shipping and packaging, My order was shipped within 48 hours of me placing the order and I received a few emails advising me of the status up until the order was dispatched. I find the link supplied to track my order very useful and the order arrived within the estimated date range. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
Fits: SUZUKI DL1000 V-STROM250, SUZUKI DL1000 V-STROM250
Exactly to AdventureMotorcycle
The quality is good and it looks great.
The Engine Guard was installed in about one hour.
I would like to purchase the Uppers next.
View detail
Fits: HONDA XR50 Motard, HONDA XR100 Motard, HONDA Ape 50, HONDA Ape 100
Excellent Parts, even though it is an Other Brand Product
It has been more than a decade since I bought a used APE 100, and I have been using it since the first air filter change, and it has been easy to change since I was a beginner both as a rider and for maintenance. View detail
Slender as the name suggests!
I often take a break from touring by hanging a helmet on Mirror. If they take Helmet, I can't leave. Sometimes I think, "What's the point of this? (Laughter)
I bought one to try.
As the name suggests, it is slender and Exactly between Mirror mounting and Handlebar Switch!
The texture is good and no discomfort.
The number is also the number of your choiceQuantity:It is good because it can be set.
I gave it 3 stars for personal use because the numbers are hard to see for my old eyes, so I gave it this rating.
I liked it so much I bought another one and installed it on my other vehicle.
I am no longer worried about Helmet being taken by Touring.
View detail
Easy installation and simple design
I bought it to put on my MT125, it has a Body, Installation Instruction Manual, and one spare key. Installation was easy. View detail
Looks pretty user-friendly.
It was already attached to the Helmet, but I thought it might work around the Handlebar because of its thin thickness, but it was not possible. I was forced to install it on the Touring bagGuard of the Rear, and it was a good decision to use the Spec. that comes with the Wire. It is very easy to use. However, the visibility of the Dial is not so good, and it may be a little difficult to unlock. View detail
It can be used normally
Chain lock for peace of mind
No matter how rugged or sturdy, when it comes to that kind of PRO.
They say there's nothing that can't be cut.
The point is how to make them take their time and give up.
I purchased 1Meter for this project.
I will try 1.2Meter next time!
It is a 4-digit Dial for unlocking, but the 4th from Left is hard!
It may be an individual difference.
View detail
Fits: HONDA 400X, HONDA 400X, HONDA BROSProduct1, HONDA BROSProduct2, HONDA CB-1, HONDA CB-1 TYPEII, HONDA CB1000R, HONDA CB1000R, HONDA CB1000SF, HONDA CB1000T2, HONDA CB1100, HONDA CB1100SE, HONDA CB1100EX, HONDA CB1100BLACKSTYLE, HONDA CB1100RS, HONDA CB1100E Package, HONDA CB1100RS Final Edition, HONDA CB1100EX Final Edition, HONDA CB1300 SUPER TOURING, HONDA CB1300SF
I use it all the time
I have used this product many times already!
That means it's a good product. I have no complaints about the price and quality so far! I will buy again!
View detail
Might be too upscale for the DRZ.
Setup to MOTARD is uncomfortable! View detail
It is too luxurious! Too carefully made and took a long time to install.
The product is so carefully made that it took me a long time to install and set it up! View detail
DAYTONA Slender Helmet lock Dial type
Installation was easy and management of the Helmet was much easier. View detail
Fits: HONDA Rebel1100 DCT, HONDA Rebel1100 DCT, HONDA Rebel1100, HONDA Rebel1100
Shared with ARAI RAPIDE-NEO and Henry beguineDHS-4
Shared with ARAI RAPIDE-NEO and Henry beguineDHS-4 at Reble 1100
[How is it used?
Used to secure helmet during touring
Was the one you received as per Image?
Street Image
Was the installation difficult?
extremely easy
How was your experience with it?
When sharing with ARAI RAPIDE-NEO and Henry beguineDHS-4, especially when removing the helmet, the helmet lock can be removed. "Key" Generally satisfactory, although there are some points where it is difficult to operate the
The attached photos are as follows.
Quantity:1 pc. Eyes:Installation status on Reble 1100
Second one.:Situation with ARAI RAPIDE-NEO fixed
Third one.:Helmet lock's "Key" The situation in which the Income is attached, "Key" Although it is difficult to manipulate the "+", it is tolerable.
Quantity:1 Set of 4 pcs. Eyes:Henry beguineDHS-4 situation with DHS-4 attached
Fifth.:Interference with Side Back when Helmet is fixed to Up. "Key" difficult to operate
Sixth.:Interference between the helmet and the side back when the helmet is fixed in the downward position, "Key" It is easier to operate. However, it does not look good.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: YAMAHA FZR250, DUCATI 749, DUCATI 748, DUCATI 748SPS, KAWASAKI ESTRELLARS, TRIUMPH DAYTONA675, MV AGUSTA BRUTALE-S, DUCATI 748SP, DUCATI 748S, DUCATI 748RS, DUCATI 748R, KAWASAKI ESTRELLARS LIMITED EDITION, DUCATI 749S, DUCATI 749R, KAWASAKI ELIMINATOR 125, DUCATI STREETFIGHTER848, DUCATI 1299, DUCATI STREETFIGHTER, DUCATI STREETFIGHTER S, DUCATI 1098
botched
I tried various products but could not find a satisfactory fit, so I decided to purchase a product that claimed to fit my car model. However, because I chose the product based on the model of the car, when I put the Cover I purchased on the Rear Carrier with the GIVI Base attached, it was too snug. I would have preferred one size larger. This is not a problem with the product, but with me, who made the wrong choice, so it has nothing to do with the direct evaluation, but I am posting it for your information. View detail
Fits: その他 , その他 , KAWASAKI Ninja H2 CARBON, DUCATI ST4S, HONDA CBR1000RR-R FIREBLADE, KAWASAKI Ninja H2R, KAWASAKI Ninja H2R, KAWASAKI Ninja H2, DUCATI ST4, DUCATI STREETFIGHTER, DUCATI STREETFIGHTER848, DUCATI STREETFIGHTER S, DUCATI ST3S, DUCATI ST3, DUCATI SS1000, DUCATI SS750, DUCATI SS750S, DUCATI ST2, DUCATI SS900, DUCATI SS900S
Used for RearCaliper
[How is it used?
Rear caliper was changed to 2POT 34mm caliper, but the effect was weaker than expected, so the pad was replaced.
MASTER：1/2-inches
Caliper：2pot 34mm
Included Pad:OrganicPad
This has now been changed to Golden Pad.
Was the one you received as per Image?
The product was exactly as shown in the pictures and there were no problems.
Was the installation difficult?
There is nothing particularly difficult about the normal Pad Replacement Level.
How was your experience with it?
With the included pad, it does not seem to work at all even if I fully step on the brake. Even when I feel that the pad has hit the disc, the braking force does not increase as expected, and although the pad is for attitude control, I need to step on it very hard to get the braking force I want.
When we replaced the pad with this pad, the braking force started when we felt the pad hit the disc, and the more we stepped on the pad, the more effective the fee ring became.
As it is Sintered Metal, I was expecting some squealing etc., but the Level is not particularly bothersome.
On the other hand, it seems to be too effective as a rear brake, and I feel that it is a complete turnaround after having reduced the size of the piston from OEM.
I recommend applying it to the Front side. for Rear, it should have been about HYPERSintered.
[Included Parts:were they on?
There are only 2 pads and no Included Parts:.
[Was there anything that disappointed you?
As I mentioned in my comments, I felt it was too effective as a Rear brake.
Other items that would be helpful
It would be very nice to have the dimensions listed for the Pad. It would be good to have the dimensions listed for other Pad as well.
View detail