You can't go wrong

I change it when I mess with the Engine When you see the CUBs which is often seen in the city with the base of Kick Arm is oil and gritty, you can change it I want to give it to you View detail

Warmth

Purchased along with the EngineOH

I compared the OEM and other manufacturers and decided on this one because it was cheaper and because of the fact that it's Takekawa

In addition, the Oil Seal of the KICKStarter Department is not available in the OEM Product with Trip

And it's a good one

But, Mr. Takekawa, it doesn't have a Sticker in it I wanted it View detail

CUB series Engine!

Oil started bleeding from the root of SUPER CUB 90's Kick Arm, so I bought it.

Thinking that it was a good opportunity, Set Oil seal asked for all replacement, and combined labor cost was 4000 yen!

Although it is the manufacture of China KYK, Kick Arm part is strengthened countermeasures against leakage and the point that it is inexpensive is the deciding factor of purchase!

Even if it is combined with the labor charge, it is not a price that was Large, so I will order the next. View detail

I'm curious about the difference between 13.7 and 13.8.

It is safe to assume that the basic structure of oil seals is the same except for the manufacturing manufacturer (and quality), so it is better to use other companies' quantity:Choose it because it's generally cheaper than Set.

The only thing I'm curious about is the size for the Kick starter spindle.
91202-302-010 is 13.7×24×5
91202-KFL-841 is 13.8×24×5

The Other Brand Product has a common part number and Dr. google searches for 13.7 and 13.8 in either size and comes up with 91202-302-010.

The diameter of the Kick Shaft I have is 13.8mm±0.02, so
Even though it rotates, it's less frequent and a little tighter is less likely to leak. Or so I think. (I think Da Strip is an extra for CellEngine that doesn't use KICK)

The conclusion, though, can be accepted as the same thing.
If you care about it, choose the OEM or the POSH with the same Seal set of Size as the OEM. and

By the way, the oil seal that leaks oil easily in our house is
?Shift arm
?Generator
?Counter Shaft
So I don't care so much about KICK. View detail

Mukawa Oil seal

I used it for the car MONKEYOverhaul じ.
The price is reasonable and it is without money.
However, one difficulty is Made in China.
Well, there may be no choice in this amount of money. View detail

When I divide, I want to change it at once.

Although it may be a replacement after Oil leaked out, it is better to replace it at the same time as maintenance that cracks Case anyway. The old Seal has a hard Rip even if it does not leak. It is not expensive, and a soft Rip feels nice.
It is the same for OEM, but Counter Shaft 's Seal requires too much attention because it touches Bearing and becomes Friction loss. View detail

Satisfied with Cost performance

I purchased thought to replace it at the time of Mission exchange,
I thought after exchanging in fact I think that it is enough to replace after leaking Oil, protecting Shaft with Vinyl Tape and replacing Ore seal with Grease so that it will not be scratched during replacement I guess this Oil Seal Set is also cheap so it's good for spare use View detail

Oil Used for leakage repair

Oil leaked from Oil seal of Shaft of Rear brake, so I exchanged it.
There was even the Oil seal with the same thickness as the OEM and with a da Strip not found in the OEM.

Three Oil seals are included and will be Rear brake Shaft, Change Pedal Shaft, Counter Shaft.

Counter Shaft's Oil seal is located where you removed the front ChainSprocket.

Although it is the replacement work, pull out the Oil seal from the outside (Be careful not to hurt Shaft though put power into force) After cleaning it, I just insert the Oil seal using Socket etc..

The price is cheap, shipping is fast, the quality of goods is also high, so I will recommend it. View detail

It is cheaper than OEM and the quality is also high.

【What made you decide the purchase?】
With cheap price [Contents].

【How was it actually used?】
I can use it without any complication as OEM Product.

【Was it difficult to install? (Hard parts case)】
It is not difficult.. I could install it in the same sense as OEM.
It is also a good impression that Grease is applied to the Rip part beforehand.

【Please tell me the point of installation and hang (in the case of Hard parts)】
Especially because it is made by Mukawa river, but not to hurt SealRip
I think that it is good to put a Vinyl bag etc. on Shaft.

[Is there anything I was disappointed about?]
There is none.

【Hope for Manufacturer - Please let me know if you have any improvement points]
It is nice that Seal of Stator base on Generator side is Set as well
think.

【Have you compared items?】
OEM Parts Number, POSH and KITACO's Oil Seal Set

[Others]
Recently the carburetor generation CUB type OEM Parts Number is also a bit expensive and it is also awkward to wait for the arrival
We bought Megawa's Set with Big. Among the various investigations, the Set of Mukawa is
I think that it is the lowest price (As of July 2015). Makawa is somewhat higher than others
However, this Oil Seal Set is cheap for some reason. It's a mystery...

The thing itself is very good. It is in no way inferior to OEM.
Manufacturer is Made in China at KOK, but it is completely usable.
KOK is MAJOR and I think that it is only good to have a mark of the producer at least clearly.
The one with No Brand has very few scarcely stamps and it is very scary to regularly use it..

so. This Seal set is inexpensive and can be used with confidence. it's recommended. View detail

Overhaul time

Many Manufacturers are out, but they are being cheap. When overhauling we will exchange every time so we are thinking no problem even if it is cheap. There is no problem than to say. View detail

He has noticed that the Seal of the Change arm of a house fitted with a motor has deteriorated, and bought here where it is a Set. I think that since it is cheap is said and it is not easy that it is said that it breaks since it does not deteriorate at t

He has noticed that the Seal of the Change arm of a house fitted with a motor has deteriorated, and bought here where it is a Set. I think that since it is cheap is said and it is not easy that it is said that it breaks since it does not deteriorate at the beginning of
. The
Seal should be checked and should be exchanged according to a situation. View detail

It is cheap and is saved. Because it is consumable goods at any rate. Kana which can be bought two pieces if pure?

It is cheap and is saved. Because it is consumable goods at any rate. Kana which can be bought two pieces if pure? View detail

It purchased for engine O/H. pure -- ? (it is unidentified) durability does ? verification of whether it is cheaper.

It purchased for engine O/H.
pure -- ? (it is unidentified) durability does ? verification of whether it is cheaper. View detail

It exchanged for the overhaul occasion. If he bought it at any rate, the pure twist was also made the product made from a functional takegawa. The difference by being pure removed the pure seal, although the spring-loaded dust lip was attached to

It exchanged for the overhaul occasion.
If he bought it at any rate, the pure twist was also made the product made from a functional takegawa.
The difference by being pure removed the pure seal, although the spring-loaded dust lip was attached to the seal by the side of a kick, but such a thing was not attached.
I feel that durability is likely to be extended for some. View detail