Reviews
Fits: HONDA CB400SUPER BOLDOR, HONDA CB400SF
Cospa is the best!
This is my second purchase.
HondaOEM
↓
KIJIMA
↓
KIJIMA
And so on
The paint is glossy.
The Fall down degree does not distort it,
When there is a slight velocity, the part of the lower part of the Engine that is in contact with the Frame distorts and bends to absorb the impact.
I bought it here because it was Point-wise a better deal than Amazon.
The bank angle will be shallower, but it is a good Knee Slider.
After use, the paint luster will disappear and the paint will rust in the areas that come in contact with the lower part of the Frame.
But with a fresh coat of rust inhibitor, there is no problem.
View detail
Fits: SUZUKI SV650, SUZUKI SV650X
sv650Engine Guard installed
I installed Engine Guard on my sv650. Installation was relatively easy. The installed impression is that it is not noticeable and looks good. I don't know about the strength because I haven't rolled it, but I think it is well made and good.
I like the look of it.
View detail
Fits: SUZUKI SV650, SUZUKI SV650X
sv650KIJIMAEngine Guard
KIJIMAEngine Guard installed on sv650.:Pair (for Left and Right) The part that connects the Quantity with the Lock nut is the Quantity:Pair (for Left and Right) It was difficult to tighten evenly. Other than that, it is easy. I am not sure how effective it is, but I like it because it is firm and comfortable. View detail
Rust and peeling paint
I had them installed by Yamaha when my car was new and they rusted and the paint peeled off after about a year, even though it was not in a wet environment. Worst quality ever.
The paint is not adhered to the Gold genus, so if you scrape it with your fingernail, the paint will peel off.
Motorcycle is Polished everywhere, only this part is already dead.
View detail
Fits: SUZUKI SV650, SUZUKI SV650X
This is the Attachment Bar
I bought the handlebar because it was inexpensive and I thought it would be easier to pull up my leg when I had a minor fall or when I was standing on the ground. I tried to pull my leg out to wake it up, but my body was not strong enough and the motorcycle was so heavy that it lay right on its side.
The Instruction Manual for the product includes It's not that durable." But I didn't know it was this weak...
It is likely to be used as a base to install a Fog Lamp, etc., but it is not so strong and flattering that it will bend if you hold it by hand and pull it. "Engine Guard" This was not a product that could be called a Attachment Bar It is
I replaced it with one from SWMo-Tech, although it is a bit more expensive.
View detail
Fits: HONDA CB400SUPER BOLDOR, HONDA CB400SF
perfect Fit good product
First, that got the package was well packed. everything was tidy in the box with protections to prevent damage from the delivery. when I unpacked the package everything was perfect. It's really easy in to install while following the instruction book. as you can the picture, it's really tidy and clean with good quality of hardwares. it looks very nice on my bike and is well protected for the bike. View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
good product
good and strong product fits perfect with my 2016 NC750X mt. need to lift up the engine little bit when remove and tighten hunger bolts. View detail
Looks good but not extremly strength
I am satisfied with the packaging and delivery, and the finish of the product is also good. Thanks a lot! If the manufacturer comes out with a wider, stiffer guard, I think I'll buy it for my SV650. Speeds like 30 mph, I feel the guard can bend if i sliped. With the guard installed, if you apply force to the upper fastening part, the iron plate moves a bit. View detail
Fits: HONDA CB400SUPER BOLDOR, HONDA CB400SF
It works fine!
It can be used without any problem.
Used on a CB400SF 2016.
The OEM Guard was rubbed and bent, so I replaced it with a KIJIMA which was cheaper.
Installation is not difficult if you have the tools.
The OEM was good because the bolts were dyed black, but this one is bare, so it is rather noticeable. The person who cares about it is attention.
Also, the Guard overhang is slightly larger than OEM. It's just my imagination, but...
I haven't measured it, so I can't say for sure.
If it's just standing muck, it's enough to scratch the Mirror, Bar End and Exhaust System, so it's recommended as a countermeasure!
View detail
Fits: SUZUKI SV650, SUZUKI SV650X
It seems to be able to protect the Engine area cheaply
I installed it to reduce the damage around the engine in the event of a fall Installation was easy as shown in the Instruction Manual
It's hard to say how far it can be protected because I haven't beaten it, but it's hard to say how far it can be protected It seems to protect up to Radiator without any damage
View detail
Looks good,but very weak
I bought this engine guard for it's low price, however it is too soft at the connection part, this may protect your bike only if it is still and it will bend. View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
insurance
We installed them as insurance for gobo. Very easy to wear. When removing Engine fixed Nut, Engine may fall off depending on the model, but there was no problem at all. Motorcycle itself is light so I do not think it will be beat down, but as an insurance. This Parts, maybe there is too little presence. View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
Only thing wrong is that Ubolt is stainless steel
I bought these and really like them for my NC700X. But when it comes time to adjust the valves you have to remove the right Ubolt to remove plastic plug so you can align timing marks. The Ubolt is stainless steel and without lubricant it galls and doesn't let the nut unthread so the thing twists off. In USA and I can't get more ubolts or don't know how to contact KIJIMA. View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
It was DamageZero in Motorcycle itself
Before this, unwillingly, they were mossed. (When I was going out for a tour with my mother behind him) Because there is Clearance, there is no foot caught, Motorcycle Body - It was intact with passengers. (Lever bent when the degree of Cover is small, but this time it has no problem at all)
When installing Center Stand, Jack-up and installed. tool (Including Torque wrench) Even arranging just fine enough to put the gold, but the installation was made easily by one person alone. (Because I wanted to install myself merely because it was not a security part, it was lol)
Although it was stated to remove Color that supports Horn's circuit in the Instruction Manual, it was possible to install by removing the Assembly which supports Horn.
View detail
Fits: HONDA CB400SUPER BOLDOR, HONDA CB400SF
Performance is sufficient.
Easy to install with Bolt-on.
Although I had the opportunity to try out Guard's performance the other day (Lol) , 0 after falling. There is no bend in the extent that Pipe got crackled about 5 m on a sliding race.
Of course, Engine is intact.
I also use it for Foot Rest when Long touring.
One disadvantage is that if you bank too hard for a solid Guard you will touch the road surface.
Even myself who is not the one who knocks down was trying to run the mountain road comfortably for a while.
I think that it is not suitable for those who run Race ish.
View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
Insurance when standing moss
Regarding the installation, you can follow the instructions as instructed and install it for as long as 30 minutes.
Since there is no Cushion material on the side that comes into contact with the Frame, we recommend that you chew a cushioning material if you do not want to scratch the Frame. We substituted the 1 mm Rubber roll with Double-sided Tape.
As if written by others, if prepared - - - I think that it is a way of using it. Accident etc. In the case of severe shock, the Damage may increase.
Things made by other companies may seem to have the same effect as Sub Frame, but there is not such a thing about here, and Damage reduction at standstill is Main.
Because it is Steel, it was good that I thought that the price would be cheaper a little more.
View detail
Fits: HONDA CB400SUPER BOLDOR, HONDA CB400SF
With standstill avoidance
It is inevitable that it falls down because it is two wheels.
I am thinking that Gold monetary mental Damage at the time of knocking down with looseness will be alleviated even a little. I do not plan to make it stand out, so purchase Black of the same color as Frame
View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
Easy to install
Installation of the Engine Guard was easy as per the handling Instruction Manual.
Engine mount bolt can be easily removed using Spinner Handlebar.
The appearance after installation is more uncomfortable than I expected, I think it is good.
View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
So the guards are nice overall. Easy installation and nice look. I was trying to lay it down on them and came to a conclusion that in case of a crash/drop it will perform it's main function. BUT: the muffler is the first to touch the ground anyway aтв o
So the guards are nice overall. Easy installation and nice look. I was trying to lay it down on them and came to a conclusion that in case of a crash/drop it will perform it's main function. BUT: the muffler is the first to touch the ground anyway aтв on the left side you will probably loose your kick stand's pin. It is not a kind of a bar that will allow your bike to stay a virgin after a drop but it will eliminate the plastic damages for sure. I would recommend this to buy. It definitely a nice protection for a buck! View detail
Fits: HONDA NC700X, HONDA NC750X, HONDA NC750S, HONDA NC700S
fast delivery.Good quality and service with webike. Would be better if there is an Mat black option to match with the rest of the bars.
fast delivery.Good quality and service with webike. Would be better if there is an Mat black option to match with the rest of the bars. View detail